T&R 100ADM Mk4 Secondary Current Injection Relay Test Set

Be the first to review this product

T&R 100ADM Mk4 has a 100 amp output for Test and Commisioning Engineers testing protective Relay Systems. Up to 100A for 1 minute.
(Ex. VAT) £4,850.00 (Inc. VAT) £5,820.00
OR

Please select a free gift below.

"100 Amp Secondary Current Injection Test Set - T and R Test Equipment 100 ADM"

  • Description

    T&R 100ADM Mk4 Secondary Current Injection Test Set

    The T&R 100ADM Mk4 is the new model from T and R Test Equipment. The 100ADM mk4 provides commissioning and maintenance engineers with a flexible system for testing protective systems. It has an easy to understand panel layout and a simple user interface. The status of every function can be seen at a glance, and there are no complex menus to navigate. The 100ADM mk4 keeps the familiar user interface of previous models but adds a new metering system that accurately measures the RMS of a single cycle. It also features a new current limit mode to provide very fine control of very low currents, even into low impedance loads. Current limit mode also assists in testing self-powered overcurrent protection as fitted to many 11kV ring man units.

    This test set has a range of outputs allowing injection of currents as low as a few mA and as high as 100A. Voltages up to 240V are available on the main outputs, allowing high impedance current relays and voltage relays to be tested. Four true RMS metering ranges are provided, allowing the full scale of the meter and trip level to be set independently of the selected output. Industry standard safety connectors are used on all inputs and outputs for convenience, reliability and safety.

    The T and R 100ADM Mk 4 is comprehensively protected by overcurrent, duty cycle and thermal trips, and keeps the user fully informed of any trip condition.

    • Clear and simple user interface
    • 0-100A output current
    • True RMS metering with single cycle capture
    • Multi-function auto-ranging timing system
    • Auxiliary DC & AC output
    • Large back-lit liquid crystal display
    • Thermal and over-current protection
    • Compact and portable
    • Automatic mains voltage selection
    • Shoulder carry strap

    A stabilised DC supply is provided to power the relay under test, along with an independently switched and isolated 110V AC output.

    A very flexible two channel timing system is provided, allowing trip times, reset times and re-close times to be quickly measured to a high degree of accuracy. The timer auto-ranges to measure from 1ms to 99999.9s.

    The T & R 100ADM mk4 can be used to test many types of single phase secondary protection including:

    • 27/59 Over and under voltage relays
    • 37 Under current
    • 51 IDMT relays
    • 50/76 Instantaneous overcurrent
    • 59G Neutral voltage displacement
    • 79 Auto-reclosers
    • 2 Time delay relays
    • 51G/50G Earth fault relays
    • 67 Directional overcurrent (basic tests)
    • 52 Miniature circuit breakers
    • Tripping relays
    • Thermal relays
    • 90V Voltage regulating relays
  • Specification

    T & R 100 ADM Main Output

    The main output on the unit has four taps, allowing the selection of output voltages up to 240V and output currents up to 200A.

     

    Current

    Output @230V

    Range

    Continuous

    5 min*

    1 min*

     

    O/CV

    Load V

    10V

    33A

    67A

    100A

     

    10.6V

    8.7V@100A

    35V

    10A

    20A

    30A

     

    36V

    32V@30A

    100V

    3A

    6A

    10A

     

    108V

    99V@10A

    240V

    1A

    2A

    3A

     

    276V

    259V@3A

    240Vdc

    1A

    2A

    3A

     

     

     

    *Off time of 15 minutes. On times based on an ambient temperature of 25°C.

    Protection: over current trip, duty cycle trip, thermal monitoring.

    I Limit Mode

    The main output has a current limit mode that gives very fine control of output currents up to 10A. It also allows fine current control into very low impedance loads such as digital relays.

     

    Current

    Output @230V

    Range

    Short Circuit

    Continuous

    5min

    2min

    O/CV

    Load V

    10V

    10A

    3A

    6A

    10A

    8.6V

    5V@6A

    35V

    3A

    1A

    2A

    3A

    29V

    132V@30A

    100V

    1A

    0.3A

    0.6A

    1A

    88V

    99V@10A

    240V

    0.3A

    0.1A

    0.2A

    0.3A

    224V

    259V@3A

    Auxiliary DC Output

    Range

    Maximum A

    Continuous Rating

    24V

    1A

    25W

    48V

    1A

    25W

    60V

    1A

    25W

    110V

    0.23A

    25W

    220V

    0.23A

    25W

    Protection: current limit

    Fixed AC Output

    Output Voltage

    Current

    110V

     

    300mA

    Protection: fuse.

    Metering

    The 100ADM output is metered by a digital true RMS system with a single cycle capture memory ammeter—whenever the timer stops and the output is switched off, the current reading is held on the display. The RMS value of a single cycle can be captured. A current trip is set to 110% of full scale of the selected metering range.

    Range

    Resolution

    Trip
    current

    Accuracy

    Aquisition
    time

    2.000A

    0.001A

    2.1A

    ±0.5% rdg±5d

    20ms

    10.00A

    0.01A

    10.5A

    ±0.5% rdg±5d

    20ms

    20.00A

    0.01A

    21A

    ±0.5% rdg±5d

    20ms

    100.0A

    0.1A

    105A

    ±0.5% rdg±5d

    20ms

    Timing System

    Range 0-999.999s/9999.99s/99999.9s autoranging
    Resolution 1/10/100ms
    Accuracy 0.01%rdg+2d (+4d current operated mode)
    Contact o/c 24V
    Contact s/c 20mA
    Vdc 24—240V

    Each contact circuit will auto-select for normally open or normally closed contacts. A DC voltage of 24—240Vdc may also be used to trigger either timer channel. Contact state is shown by an LED.

    Supply Requirements

    115V/230V ±10% auto-selecting 50/60Hz 1ph 1100VA max.

    Safety

    An earth terminal is provided for connection to a local earth. The unit is designed to comply with BSEN61010 and is CE marked.

    Temperature Range

    Storage -20°C to 60°C
    Operating 0°C to 45°C

    Standard Accessories

    The T and R 100ADM mk4 is supplied with operating manual, mains lead and, output lead set and spare fuses.

    Optional Accessories

    100ADM-F filter unit, RB10 resistor box, printer kit, ADMlog software.

    The unit is supplied as standard in an aluminium case with removable lid. The unit is also available in a plastic Pelicase as an option. Please note that the Pelicase lid is not removable.

    Weights and Dimensions

     T and R 100ADM Dimensions Weight
    Pelicase unit 560mm x 456mm x 265mm 23.3kg
  • Supplied Accessories

    • T and R 100ADM Mk4 Relay Test Set
    • 2 x 5m 25mm2 200A leads terminated in M10 ring crimps
    • 2 x 5m 2.5mm2 25A leads terminated in retractable shroud 4mm plugs
    • 1 x 5m 2 core timer lead terminated in retractable shroud 4mm plugs
    • Plastic carrying case for test leads
    • Operating manual
    • Mains lead
    • Spare fuses
  • Product Questions

    Please Sign in or Create an account to post a question.

    There are no entries.

  • Reviews

    There are currently no reviews for this product. If you have previously purchased it please leave a review using our quick and easy form to the right.

    Write Your Own Review

    Only registered users can write reviews. Please, log in or register

  • Delivery Information

    At Test-Meter.co.uk we understand the importance of a reliable delivery service when shopping online. Especially when the goods are often essential to your working day. If your goods are required by a certain date please feel free to contact us for an honest and realistic indication whether this can be met.

    We use DPD/Interlink for all larger items and Royal Mail for smaller items and accessories. With DPD/Interlink you will receive a 1 hour delivery window on the day of delivery via e-mail/text so you will not have to wait around all day. We also offer delivery options for goods required urgently on certain products, all which are sent by DPD/Interlink on a fully traceable and manageable service.

    Our charges for UK deliveries:

    • FREE Delivery (on select products only): typically 2-5 working days*
    • Standard Delivery at £4.95: 2-3 working days
    • Next Working Day Delivery (on select products only) at £8.95
    • Pre 10.30am Next Working Day Delivery (on select products only) at £19.95*
    • Saturday Pre 12pm Delivery (on select products only) at £19.95*
    • Sunday Pre 12pm Delivery (on select products only) at £19.95*

    *UK mainland only

    NOTE! For next working day or Saturday delivery options the order MUST be placed no later than 3pm on the working day before delivery is required. After 3pm, please arrange with our staff before selecting a priority delivery service. Priority services are available to UK mainland residents only.

    Customers outside the UK:

    Test-Meter.co.uk exports to many countries all over the world. Prices for shipping vary on location and weight/dimensions. Costs are calculated for certain countries at the checkout. If your country is not included in this list please e-mail admin@test-meter.co.uk with your name, address and the items you would like to order for an accurate shipping quote.